View LTC4050_213687.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC4050 Lithium-Ion Linear Battery Charger with Thermistor Interface FEATURES
s s
DESCRIPTIO
s s s s s s s
s s s s
Complete Standalone Linear Charger Controller for 1-Cell Lithium-Ion Batteries Thermistor Interface for Battery Temperature Sensing Preset Charge Voltage with 1% Accuracy Programmable Charge Current C/10 Charge Current Detection Output Programmable Charge Termination Timer Input Supply (Wall Adapter) Detection Output 4.5V to 10V Input Voltage Range Automatic Sleep Mode When Input Supply is Removed (Only 5A Battery Drain) Automatic Trickle Charging of Low Voltage Cells Automatic Battery Recharge Battery Insertion Detection Space Saving 10-Pin MSOP Package
The LTC (R)4050-4.1/LTC4050-4.2 are complete standalone constant-current/constant-voltage linear charge controllers for lithium-ion (Li-Ion) batteries. Charge current is programmable and final float voltage has 1% accuracy. When the input supply is removed, the LTC4050 automatically enters a low quiescent current sleep mode, dropping the battery drain current to 5A. An internal comparator detects the near-end-of-charge (C/10) condition while a programmable timer, using an external capacitor, sets the total charge time. Fully discharged cells are automatically trickle charged at 10% of the programmed current until cell voltage exceeds 2.49V. The thermistor interface suspends charging if the cell temperature is outside of a 0C to 50C temperature window. The LTC4050 begins a new charge cycle when a discharged battery is connected to the charger or when the input power is applied. In addition, a new charge cycle is automatically started if the battery remains connected to the charger and the cell voltage drops below 3.88V for 4.1V cells or below 3.98V for 4.2V cells. The LTC4050 is available in the 10-pin MSOP package.
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATIO S
s s s
Cellular Phones Handheld Computers Charging Docks and Cradles
TYPICAL APPLICATIO
Single Cell 4.2V 500mA Li-Ion Battery Charger
VIN 6V MBRM120T3 8 1k 1k 3 CHRG VCC SENSE DRV 0.2 9 7 Si9430DY IBAT = 500mA * 19.6k 10F 1F
600 VBAT = 3.7V 500 CHARGE CURRENT (mA) 400 300 200 100
LTC4050-4.2 10 4 0.1F ACPR TIMER GND 5 BAT PROG NTC 2 1 6
+ 4.2V
Li-Ion CELL
10k NTC T DALE NTHS-1206N02
*SHUTDOWN INVOKED BY FLOATING THE PROG PIN
4050 TA01
U
Charge Current vs Thermistor Temperature
0 50 100 -50 -25 25 75 0 THERMISTOR TEMPERATURE (C) 125
4050 TA05
U
U
4050f
1
LTC4050 ABSOLUTE MAXIMUM RATINGS
(Note 1)
PACKAGE/ORDER INFORMATION
ORDER PART NUMBER
TOP VIEW BAT NTC CHRG TIMER GND 1 2 3 4 5 10 9 8 7 6 ACPR SENSE VCC DRV PROG
Input Supply Voltage (VCC) ...................................... 12V SENSE, DRV, BAT, SEL, TIMER, PROG, CHRG, ACPR .................- 0.3V to 12V Operating Temperature Range (Note 2) . - 40C to 85C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
LTC4050EMS-4.1 LTC4050EMS-4.2 MS PART MARKING LTTW LTTX
MS PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 140C, JA = 180C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 6V unless otherwise noted.
SYMBOL VCC ICC PARAMETER Input Supply Voltage Input Supply Current Charger On, Current Mode Shutdown Mode Sleep Mode (Battery Drain Current) LTC4050-4.1; 5V VCC 10V, 0C TA 85C LTC4050-4.2; 5V VCC 10V, 0C TA 85C LTC4050-4.1; 5V VCC 10V LTC4050-4.2; 5V VCC 10V RPROG = 19.6k, RSENSE = 0.2 RPROG = 19.6k, RSENSE = 0.2 RPROG = 97.6k, RSENSE = 0.2 CONDITIONS
q q q
ELECTRICAL CHARACTERISTICS
MIN 4.5
TYP 1.3 1.3 5
MAX 10 3 3 15 4.141 4.242 4.141 4.242 535 585 140 90 2.58 4.5
UNITS V mA mA A V V V V mA mA mA mA V V mV V
VBAT
Regulated Output (Float) Voltage in Constant Voltage Mode
q q q
4.059 4.158 4.039 4.137 440 415 60 20 2.41
4.1 4.2 4.1 4.2 500 100 55 2.49 4 130 3.6
IBAT
Current Mode Charge Current
ITRIKL VTRIKL VUV VUV VMSD VASD IPROG VPROG VACPR ICHRG VCHRG RHOT RCOLD
Trickle Charge Current Trickle Charge Threshold Voltage VCC Undervoltage Lockout Voltage VCC Undervoltage Lockout Hysteresis PROG Pin Manual Shutdown Threshold Voltage Automatic Shutdown Threshold Voltage PROG Pin Current PROG Pin Voltage ACPR Pin Output Low Voltage CHRG Pin Weak Pull-Down Current CHRG Pin Output Low Voltage Thermistor Resistance for Hot Fault Thermistor Resistance for Cold Fault
VBAT = 2V, RPROG = 19.6k, ITRIKL = (VCC - VSENSE)/0.2 q
q q
(VCC - VBAT) High to Low (VCC - VBAT) Low to High Internal Pull-Up Current, No RPROG PROG Pin Source Current, VPROG 5mV RPROG =19.6k IACPR = 5mA VCHRG = 1V ICHRG = 5mA
q
25 40 300
54 69 2.3 2.47 0.525 32 0.525
85 100
3.7 25
4.1 28.5
4.4 31
2
U
W
U
U
WW
W
mV mV A A V V A V k k
4050f
LTC4050
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 6V unless otherwise noted.
SYMBOL IC/10 tTIMER VRECHRG PARAMETER 10% Charge Current Indication Level TIMER Accuracy Recharge Threshold Voltage CONDITIONS RPROG = 19.6k, RSENSE = 0.2 CTIMER = 0.1F VBAT from High to Low (LTC4050-4.1) VBAT from High to Low (LTC4050-4.2) Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. 3.83 3.93
q
ELECTRICAL CHARACTERISTICS
MIN 25
TYP 50 10 3.88 3.98
MAX 100
UNITS mA % V V
Note 2: The LTC4050E is guaranteed to meet performance specifications from 0C to 70C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls.
TYPICAL PERFOR A CE CHARACTERISTICS
Charge Current vs Temperature
540 RPROG = 19.6k RSEN = 0.2 VBAT = 3V VCC = 6V 520 IBAT (mA) IBAT (mA) 520
ITRKL (mA)
500
480
460 -50
-25
75 0 25 50 TEMPERATURE (C)
Trickle Charge Current vs VCC
70 RPROG = 19.6k RSEN = 0.2 65 VBAT = 2V TA = 25C 60 ITRKL (mA) 55 50 45 40 4 6 VCC (V)
LTC4050 G04
VTRKL (V)
VTRKL (V)
8
UW
100
LTC4050 G01
Charge Current vs VCC
70 RPROG = 19.6k 515 RSEN = 0.2 VBAT = 3V 510 TA = 25C 505 500 495 490 485 480 125 4 6 VCC (V)
LC4050 G02
Trickle Charge Current vs Temperature
RPROG = 19.6k RSEN = 0.2 65 VBAT = 2V VCC = 6V 60 55 50 45 40 -50 -25
8
10
50 25 75 0 TEMPERATURE (C)
100
125
LTC4050 G03
Trickle Charge Threshold Voltage vs Temperature
2.51 VCC = 6V RPROG = 19.6k
Trickle Charge Threshold Voltage vs VCC
2.55 RPROG = 19.6k 2.54 TA = 25C
2.50
2.53 2.52
2.49
2.51 2.50 2.49 2.48
2.48
2.47
2.47 2.46
10
2.46 -50 -25
50 25 0 75 TEMPERATURE (C)
100
125
2.45 4 6 VCC (V) 8 10
LTC4050 G06
LTC4050 G05
3
LTC4050 TYPICAL PERFOR A CE CHARACTERISTICS
Recharge Threshold Voltage vs Temperature
4.1 VCC = 6V LTC4050-4.2 2.470 VRECHRG (V) VPROG (V) 3.9 LTC4050-4.1 2.465 2.460 3.8 2.455 3.7 -50 2.450 -50 -25 2.46 VPROG (V) 2.48 2.480 2.475 4.0
-25
75 0 25 50 TEMPERATURE (C)
Timer Accuracy vs Temperature
110 VCC = 6V VBAT = 3V CTIMER = 0.1F 110
105 TIMER (%) TIMER (%)
100
RHOT (k)
95
90 -50
-25
75 0 25 50 TEMPERATURE (C)
NTC RCOLD Threshold Voltage vs Temperature
29.0 28.9 28.8 28.7
RCOLD (k)
VCC = 6V
28.6 28.5 28.4 28.3 28.2 28.1 -50
4.100
RCOLD (k)
RHOT (k)
-25
0 25 50 75 TEMPERATURE (C)
4
UW
100
LTC4050 G07
PROG Pin Voltage vs Temperature
VCC = 6V RPROG = 19.6k 2.50
PROG Pin Voltage vs VCC
RPROG = 19.6k TA = 25C
2.49
2.47
125
50 25 75 0 TEMPERATURE (C)
100
125
2.45
4
6 VCC (V)
8
10
LTC4050 G09
LTC4050 G08
Timer Accuracy vs VCC
VBAT = 3V CTIMER = 0.1F TA = 25C 4.16 4.14 4.12 100 4.10 4.08 95 4.06 90 4 5 6 7 VCC (V) 8 9 10
NTC RHOT Threshold Voltage vs Temperature
VCC = 6V
105
100
125
4.04 -50 -25
50 25 75 0 TEMPERATURE (C)
100
125
LTC4050 G10
LTC4050 G11
LTC4050 G12
NTC RHOT Threshold Voltage vs VCC
4.150 TA = 25C 28.60
NTC RCOLD Threshold Voltage vs VCC
TA = 25C
4.125
28.55
28.50
4.075
28.45
4.050 100 125
4
6 VCC (V)
8
10
LT4050 G14
28.40
4
6 VCC (V)
8
10
LTC4050 G15
LTC4050 G13
LTC4050 PIN FUNCTIONS
BAT (Pin 1): Battery Sense Input. A precision internal resistor divider on this pin sets the final float voltage. The resistor divider is disconnected in sleep mode to reduce the current drain on the battery. A bypass capacitor of 10F or more is required to keep the loop stable when the battery is not connected. NTC (Pin 2): Thermistor Interface Input. A 10k Dale Curve 2 NTC thermistor (or other 10k NTC thermistor with a room temperature beta of around 3400) is connected from this pin to ground. The charge cycle will be disabled and the timer will be placed on hold if the thermistor temperature is above 50C or below 0C. CHRG (Pin 3): Charge Status Open-Drain Output. When the battery is charging, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge current drops to 10% of the full-scale current for more than 15ms, the N-channel MOSFET turns off and a 32A current source is connected from the CHRG pin to GND. When the timer runs out or the input supply is removed, the current source is disconnected and the CHRG pin becomes high impedance. TIMER (Pin 4): Timer Capacitor and Constant-Voltage Mode Disable Input Pin. The timer period is set by placing a capacitor, CTIMER, to GND. The timer period is tTIMER = (CTIMER * 3 hours)/(0.1F). Shorting the TIMER pin to GND will disable the internal timer function and the C/10 function. GND (Pin 5): Ground. PROG (Pin 6): Charge Current Program and Shutdown Input Pin. The charge current is programmed by connecting a resistor, RPROG to ground. The charge current is IBAT = (VPROG * 800)/(RPROG * RSENSE). The IC can be forced into shutdown by floating the PROG pin and allowing the internal 2.3A current source to pull the pin above the 3.6V shutdown threshold voltage. DRV (Pin 7): Drive Output Pin for the P-Channel MOSFET or PNP Transistor. The impedance is high at this pin, therefore, if a PNP pass transistor is used, it must have high gain. VCC (Pin 8): Positive Input Supply Voltage. VCC can range from 4.5V to 10V. Bypass this pin with a 1F capacitor. When VBAT is within 54mV of VCC, the LTC4050 is forced into sleep mode, dropping ICC to 5A. SENSE (Pin 9): Current Sense Input. A sense resistor, RSENSE, must be connected from VCC to the SENSE pin. Select a resistor value that will develop approximately 100mV at the programmed full-scale charge current. This resistor is chosen using the following equation: RSENSE = (VPROG * 800)/(RPROG * IBAT) ACPR (Pin 10): Wall Adapter Present Output. When the input voltage (wall adaptor) is applied to the LTC4050, this pin is pulled to ground by an internal N-channel MOSFET that is capable of sinking 5mA suitable for driving an external LED.
U
U
U
4050f
5
LTC4050 BLOCK DIAGRA W
VCC 8
UV
2
3
CHRG C4
C/10 STOP RECHRG C/10 32A ACPR SHDN LOGIC SLP
720
4
OSCILLATOR 3.6V VREF
COUNTER
10
ACPR C3
+ -
+
A1
VA
-
VCC 2.3A VREF 2.47V CHARGE PROG RPROG GND
4050 BD
6 BATTERY CURRENT IBAT = (2.47V * 800)/(RPROG * RSENSE)
6
-
+
TIMER
LBO
C2
-
+
+
-
+
-
NTC
+ +
C1 80 800
28.6k
- +
C5 3.88V (LTC4050-4.1) 3.98V (LTC4050-4.2)
-
RSENSE SENSE 9
-
+ - +
54mV
-
CA DRV 7
BAT
1
5
4050f
LTC4050 OPERATIO
The LTC4050 is a linear battery charger controller. The charge current is programmed by the combination of a program resistor (RPROG) from the PROG pin to ground and a sense resistor (RSENSE) between the VCC and SENSE pins. RPROG sets a program current through an internal trimmed 800 resistor setting up a voltage drop from VCC to the input of the current amplifier (CA). The current amplifier servos the gate of the external P-channel MOSFET to force the same voltage drop across RSENSE which sets the charge current. When the voltage at the BAT pin approaches the preset float voltage, the voltage amplifier (VA) will start sinking current which reduces the voltage drop across RSENSE, thus reducing the charge current. A charge cycle begins when the voltage at VCC pin rises above the UVLO level, a program resistor is connected from the PROG pin to ground, and the NTC thermistor temperature is between 0C and 50C. At the beginning of the charge cycle, if the battery voltage is below 2.49V, the charger goes into trickle charge mode. The trickle charge current is 10% of the full-scale current. If the cell voltage stays low for one quarter of the total charge time, the charge sequence will terminate. The charger goes into the fast charge constant-current mode after the voltage on the BAT pin rises above 2.49V. In constant-current mode, the charge current is set by the combination of RSENSE and RPROG. When the battery approaches the final float voltage, the charge current will begin to decrease. When the current drops to 10% of the full-scale charge current, an internal comparator will turn off the pull-down N-channel MOSFET
U
at the CHRG pin and connect a weak current source to ground, indicating that the battery is nearly fully charged (C/10 occurs at approximately 94% charge). An external capacitor on the TIMER pin sets the total charge time. After a time-out occurs, the charge cycle is terminated and the CHRG pin is forced high impedance. To restart the charge cycle, remove the input voltage and reapply it, or momentarily float the PROG pin. Replacing the battery when charging will cause the timer to be reset if the cell voltage of the new battery is below 3.88V (for 4.1V cells) or 3.98V (for 4.2V cells). If the voltage is above 3.88V(for 4.1V cells) or 3.98V (for 4.2V cells) the timer will continue for the remaining charge time. In the case when a time out has occurred, a new battery with a cell voltage of less than 3.88V or 3.98V can be inserted and charged automatically with the full programmed charge time. For batteries like lithium-ion that require accurate final float voltage, the internal 2.47V reference, voltage amplifier and the resistor divider provide regulation with 1% (max) accuracy. The charger can be shut down by floating the PROG pin. An internal current source will pull it high and clamp at 3.5V. When the input voltage is not present, the charger goes into a sleep mode, dropping ICC to 5A. This greatly reduces the current drain on the battery and increases the standby time.
4050f
7
LTC4050 APPLICATIONS INFORMATION
Charger Conditions The charger is off when any of the following conditions exist: the voltage at the VCC pin is below 4V, the voltage at the VCC pin is greater than 4V but is less than 54mV above VBAT, the PROG pin is floating, the timer has timed out or the thermistor temperature is outside the acceptable range. In this condition, the DRV pin is pulled to VCC and the internal resistor divider is disconnected to reduce the current drain on the battery. Undervoltage Lockout (UVLO) An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above the undervoltage lockout threshold of 4V. To prevent oscillation around VCC = 4V, the UVLO circuit has built-in hysteresis. Trickle Charge and Defective Battery Detection At the beginning of the charging sequence, if the battery voltage is low (below 2.49V), the charger goes into trickle mode. In this mode, the charge current is reduced to 10% of the full-scale current. If the low cell voltage persists for one quarter of the total charge time, the battery is considered defective, the charge cycle is terminated and the CHRG pin output becomes high impedance. Shutdown The LTC4050 can be forced into shutdown by floating the PROG pin and allowing the internal 2.3A current source to pull the pin above the 3.6V shutdown threshold voltage. In shutdown, the DRV pin is pulled up to VCC, turning off the external P-channel MOSFET and resetting the internal timer.
V+ 8 VCC LTC4050 CHRG 3 400k 2k OUT IN
4050 F01
Figure 1. Microprocessor Interface
4050f
8
U
W
U
U
Programming Charge Current The formula for the battery charge current (see Block Diagram) is: IBAT = (IPROG)(800/RSENSE) = (2.47V/RPROG)(800/RSENSE) or RPROG = (2.47V/IBAT)(800/RSENSE) where RPROG is the total resistance from the PROG pin to ground. For example, if 0.5A charge current is needed, select a value for RSENSE that will drop 100mV at the maximum charge current. RSENSE = 0.1V/0.5A = 0.2, then calculate: RPROG = (2.47V/500mA)(800/0.2) = 19.76k For best stability over temperature and time, 1% resistors are recommended. The closest 1% resistor value is 19.6k. Programming the Timer The programmable timer terminates the charge cycle. Typically when charging at a 1C rate, a discharged Li-Ion battery will become fully charged in 3 hours. For lower charge current rates, extend the time accordingly. The length of the timer is programmed by an external capacitor at the TIMER pin. The total charge time is: Time (Hours) = (3 Hours) * (CTIMER/0.1F) or CTIMER = 0.1F * Time (Hours)/3 Hours The timer starts when an input voltage greater than 4V is applied and the program resistor is connected to ground. After a time-out occurs, the CHRG output will go high impedance to indicate that charging has stopped. To disable the timer function, short the TIMER pin to GND.
VDD
PROCESSOR
LTC4050 APPLICATIONS INFORMATION
CHRG Status Output Pin (C/10) When the charge cycle starts, the CHRG pin is pulled to ground by an internal N-channel MOSFET that can drive an LED. When the charge current drops to 10% of the fullscale current (C/10), the N-channel MOSFET turns off and a weak 32A current source to ground is connected to the CHRG pin. After a time-out occurs, the pin goes high impedance. By using two different value pull-up resistors, a microprocessor can detect three states from this pin (charging, C/10 and stop charging). See Figure 1. When the LTC4050 is in charge mode, the CHRG pin is pulled low by an internal N-channel MOSFET. To detect this mode, force the digital output pin, OUT, high and measure the voltage at the CHRG pin. The N-channel MOSFET will pull the pin low even with a 2k pull-up resistor. Once the charge current drops to 10% of the fullscale current (C/10), the N-channel MOSFET turns off and a 32A current source is connected to the CHRG pin. The IN pin will then be pulled high by the 2k pull-up. By forcing the OUT pin into a high impedance state, the current source will pull the pin low through the 400k resistor. When the internal timer has expired, the CHRG pin will change to high impedance state and the 400k resistor will then pull the pin high to indicate charging has stopped. The CHRG pin open-drain device will turn on if the BAT pin falls below the trickle charge threshold and the LTC4050 has neither timed out nor been put into shutdown. For example, if the battery and NTC thermistor are both disconnected from the typical application circuit, the BAT voltage will collapse due to the thermal fault and CHRG will pull low. Entering shutdown by floating the PROG pin will prevent the CHRG pulldown from turning on. ACPR Output Pin The LTC4050 has an ACPR output pin to indicate that the input supply (wall adapter) is higher than 4V and 54mV or more above the voltage at the BAT pin. When both conditions are met, the ACPR pin is pulled to ground by an N-channel MOSFET that is capable of driving an LED. Otherwise, this pin is in a high impedance state. Gate Drive Typically the LTC4050 controls an external P-channel MOSFET to supply current to the battery. An external PNP transistor can also be used as the pass transistor instead of the P-channel MOSFET. Due to the low current gain of the current amplifier (CA), a high gain Darlington PNP transistor is recommended to avoid excessive charge current error. The gain of the current amplifier is around 0.6A/mV. For every 1A of base current, a 1.6mV of gain error shows up at the inputs of CA. With RPROG = 19.6k (100mV across RSENSE), it represents 1.67% of error in charge current. Battery Detection The LTC4050 can detect the insertion of a new battery. When a battery with a voltage of less than 3.88V (for 4.1V cells) or 3.98V (for 4.2V cells) is inserted, the LTC4050 resets the timer and starts a new charge cycle. If the cell voltage of the new battery is above 3.88V (for 4.1V cells) or 3.98V (for 4.2V cells), a new charge cycle will not begin. If a new battery (with cell voltage above 3.88V) is inserted while in the charging process, the timer will not be reset, but will continue until the timer runs out. After a time out has occurred and the battery remains connected, a new charge cycle will begin if the battery voltage drops below the recharge threshold of 3.88V (for 4.1V cells) or 3.98V (for 4.2V cells) due to self-discharge or external loading. Stability The charger is stable without any compensation when a P-channel MOSFET is used as the pass transistor. However, a 10F capacitor is recommended at the BAT pin to keep the ripple voltage low when the battery is disconnected.
U
W
U
U
4050f
9
LTC4050 APPLICATIONS INFORMATION
If a PNP transistor is chosen as the pass transistor, a 1000pF capacitor is required from the DRV pin to VCC. This capacitor is needed to help stabilize the voltage loop. A 10F capacitor at the BAT pin is also recommended when a battery is not present. VCC Bypass Capacitor Many types of capacitors can be used for input bypassing. However, caution must be exercised when using multilayer ceramic capacitors. Because of the self resonant and high Q characteristics of some types of ceramic capacitors, high voltage transients can be generated under some start-up conditions, such as connecting the charger input to a hot power source. These transients can be minimized by using X5R dielectric capacitors and/or by adding a 1.5 resistor in series with the ceramic input capacitor. For more information, refer to Application Note 88. Thermistor Interface A thermistor connected to the NTC (negative temperature coefficient) pin can be used to sense the battery temperature to determine if the battery is within an acceptable temperature range for charging (between 0C and 50C). A Dale (curve 2) 10k thermistor is recommended although many other types of thermistors can also be used. For example, a BetaCHIP (curve 7) 10k thermistor or other 10k thermistors with a room temperature beta of approximately 3400 will work well. The thermistor is connected from NTC (pin 2) to ground and is biased up by an internal 28.6k trimmed thin film resistor that connects to VCC through a P-channel MOSFET. This MOSFET also biases an internal resistor string to ground, from which voltage thresholds of approximately VCC/2 and VCC/8 are derived. The NTC pin is compared to these thresholds by two comparators that have wired-OR outputs. The thresholds are selected such that an overtemperature condition will occur when the thermistor resistance is less than approximately 4.1k and undertemperature condition will occur when the thermistor resistance is greater than approximately 28.5k. These correspond to thermistor temperatures of 50C and 0C for the specific type of thermistor listed above (many others will be close enough for most purposes). The MOSFET is turned off during undervoltage conditions, preventing the dividers that are biased from it from drawing current from the battery when input power is removed. The drop across the MOSFET is common to both resistor dividers and does not cause any loss of accuracy in the circuit. The comparators have approximately 10mV of hysteresis to prevent oscillations around the trip points. When an undertemperature or overtemperature condition is sensed, the current amplifier pulldown is disabled and DRV is pulled high, the timer is placed in a hold condition with the count frozen until the battery temperature is within an acceptable range. The end-of-charge comparator is also disabled to prevent a premature end of charge signal due to the lack of battery charging current.
NTC 2 10k DALE CURVE 2 NTC THERMISTOR
10
+
28.6k
+
-
-
U
UV
W
U
U
NTC Interface Circuitry
VCC
TBAD (TO CA, EOC, TIMER)
4050 AI
4050f
LTC4050 PACKAGE DESCRIPTIO U
MS Package 10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661)
0.889 0.127 (.035 .005) 3.2 - 3.45 (.126 - .136) 3.00 0.102 (.118 .004) (NOTE 3) 10 9 8 7 6 0.497 0.076 (.0196 .003) REF DETAIL "A" 0 - 6 TYP 12345 0.53 0.01 (.021 .006) DETAIL "A" 0.18 (.007) SEATING PLANE 0.17 - 0.27 (.007 - .011) TYP 0.13 0.076 (.005 .003)
MSOP (MS) 0802
5.23 (.206) MIN
0.50 0.305 0.038 (.0197) (.0120 .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT
0.254 (.010) GAUGE PLANE
4.90 0.15 (1.93 .006)
3.00 0.102 (.118 .004) NOTE 4
1.10 (.043) MAX
0.86 (.034) REF
NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.50 (.0197) BSC
4050f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
LTC4050 TYPICAL APPLICATIO S
Linear Charger Using a PNP Transistor
VIN 6V MBRM120T3
1k 3 10
0.1F
Single Cell 4.1V, 1.5A High Efficiency Li-Ion Battery Charger
VIN 6V MBRS130LT3
RELATED PARTS
PART NUMBER LT(R)1510-5 LT1512 LT1620 LTC1729 DESCRIPTION 500kHz Constant-Voltage/Constant-Current Battery Charger SEPIC Battery Charger Rail-to-Rail Current Sense Amplifier Termination Controller for Li-Ion COMMENTS Most Compact, Up to 1.5A, Charges NiCd, NiMH, Li-Ion Cells VIN Can Be Higher or Lower Than Battery Voltage, 1.5A Switch Precise Output Current Programming, Up to 32V VOUT, Up to 10A IOUT Time or Charge Current Termination, Automatic Charger/Battery Detection, Status Output, Preconditioning, 8-Lead MSOP; Timer; AC Adapter Present Detection; No Firmware Required CC/CV Charges Li-Ion Cells, 8-Lead MSOP, Programmable Timer; No Adapter Present Detection; Programmable Timer; No Firmware Required Complete Standalone Charger, Thermal Regulator Prevents Overheating Only Two External Components; No Diode; No Sense Resistor; VPROG Allows Monitoring ICHARGE Detects Maximum ICHARGE for Safety; No MOSFET; No Diode; No Firmware Required USB and Wall Adapter Input, 100mA/500mA or Up to 1.25A Charge Current Standalone Charger
4050f LT/TP 0203 2K * PRINTED IN THE USA
LTC1731 LTC1732 LTC1733 LTC1734 LTC1734L LTC4052 LTC4053
Li-Ion Linear Battery Charger Controller Firmware Required Li-Ion Linear Battery Charger Controller Li-Ion Linear Charger with Thermal Regulation ThinSOT Li-Ion Linear Battery Charger Controller Li-Ion Linear Battery Pulse Charger USB Compatible Li-Ion Battery Charger
ThinSOT is a trademark of Linear Technology Corporation.
12
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507
q
U
1k 8 VCC CHRG ACPR SENSE DRV 9 7
1nF
10k
0.2
1F
ZTX749 2N5087 IBAT = 500mA
LTC4050-4.2 4 TIMER BAT PROG NTC 2 GND 5 1 6 19.6k 10F
+
4.2V Li-Ion CELL
10k NTC T DALE NTHS-1206N02
4050 TA02
1k
1k 8 3 10 VCC 9 SENSE 7
0.47F 4.7 8 11 LTC1693-5 4 0.082 1/4W
+
22F
CHRG ACPR
3 7 Si2305DS MBRS130LT3
DRV LTC4050-4.1 1 BAT 6 PROG GND 5
4 0.1F
TIMER NTC 2
19.6k
T
15H CDRH6D28-150NC
+
10k NTC DALE NTHS-1206N02
4.1V Li-Ion CELL
+
220F
4050 TA04
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2002

▲Up To Search▲

Price & Availability of LTC4050

	To Download LTC4050 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .